How to Make Solar Led Street Light Fixture?

Now more and more countries are plan to make solar led street light fixture.Because traditional street lamps need to use a lot of electricity and have labor costs,and solar led street light have a lot of benefits.Firstly,the designer need to know the technical data for the traditional street lamp.

Probably speaking,the ratio of power between traditional street lamps and solar street lamps is 1:5.It mean that if AC sodium street lamp or AC halogen street lamp power is 100W,then you can chose 20 Watt led solar street lights.Secondly,solar led street light fixture designer need to calculate the solar panel and battery capacity.

The solar panel and battery capacity should base on the light working time.Normally We design 20 Watt led solar street lights working time is 12 hours per night.Because it will have a lot of human appear in the road from 6PM to 12PM,and it will have less human or nobody appear in the road from 1AM to 6AM.

In order to save the power,we can set 20 Watt led solar street lights work in 100% power in 6 hours,50% power in another 6 hours.Then when it is in 6PM to 12PM,the light is very bright.When it is in 1AM to 6AM,the light will be use in 50% power status,save half of the power.

Thirdly,traditional street lamp pole have not included solar panel support and battery support.So it need to add solar panel support and battery support in solar led street light fixture project.The solar panel support size should base on solar panel drawing,solar panel drawing include solar panel size and solar panel frame hole position.

Use suitable screw fix the solar panel on the solar panel bracket.Following these steps,we can make solar led street light fixture smoothly.Mostly,this is a one time investment,after 2–3 year’s using,you can call back your investment and use free power later.

FOSHAN MARS SOLAR TECHNOLOGY CO.

,LTDAdd:2 floor,№3 Building, Lianfeng industrial zone,ZhangCha Chancheng District,Foshan City,Guangdong Province.ChinaMob:86–757–82705605 86 15302966051Email:admin@solarpowermanufacturer.comwww.solarledfactory.com

·RELATED QUESTION

Why is the speed of the centrifugal compressor is kept higher than that of centrifugal pump?

Centrifugal gas compressors are limited by a stress limited tip speed. In general, smaller frame sizes have higher nominal speeds than larger units mainly due to the larger impeller stresses in larger wheels. Mathematically, stress is directly proportional to the square of tip speed. With less denser materials, you can drive to higher speeds. A typical example would be an automotive turbocharger compressing air, made of single aluminum stages where 60,000–100,000 RPMs are not unheard of. The process gas compressor are limited to lower speeds due to a steel alloy makeup and practical constraints of rotor dynamics and thermomechanical stress in multi stage units.

How to Make Solar Led Street Light Fixture? 1

GET IN TOUCH WITH Us
recommended articles
News Application
Wholesale New Lamps IP65 Waterproof SMD 30W 60 90 100 Watt Led Street Light for Sale
Wholesale New Lamps IP65 Waterproof SMD 30W 60 90 100 Watt Led Street Light for Sale
The color rendering index of 100 watt led street light is much higher than that of high-pressure sodium lamp. The color rendering index of high-pressure sodium lamp is only about 23, while the color rendering index of LED street lamp is more than 75. From the perspective of visual psychology, the illumination of LED street lamp can be reduced by more than 20% on average compared with that of high-pressure sodium lamp.100 watt led street light has automatic control energy-saving device, which can achieve the maximum possible power reduction and power saving under the condition of meeting the lighting requirements of different periods. It can realize computer dimming, time-sharing control, light control, temperature control, automatic inspection and other humanized functions. 100 watt led street light SL03 description 1、Modularization & plug technology, convenient maintenance, no need any tools. 2、Cellular heat dissipation and the whole structured dissipation technology, good heat dissipation performance. 3、Double coupling IP65 protection level, super waterproof performance. 4、Single LED lamp damaged does not affect the other lamp working. 5、Multi-channel constant current driver power supply, single module can be hot plug. 6、Human ergonomics light distribution, uniform road lighting. 7、Multiple modules free combination, so the LED modulariztion provides a great lighting solution for industrial applications. 100 watt led street light shape structure For the external protection of 100 watt led street light, it is recommended to use soft ceramic heat dissipation paint for LED lamps. This spray type soft ceramic heat dissipation paint can be directly sprayed on the outside of LED lamps and lanterns, which is easy to operate and can be adapted to various shapes of heat dissipation structures, and can also be adjusted to different colors to meet the needs of landscape design. The soft ceramic particles in the spray type heat dissipation paint are treated by nano technology. The fine particles are not only easy to be operated by the spray gun, but also make the heat conduction particles on the same coating area more and denser, make the area of temperature volatilization and dissipation larger, and make the heat energy of LED lamps quickly transmit out. Soft ceramic heat dissipation paint is a thermosetting material, which conforms to ROHS environmental protection and Safety specifications. The construction procedure is simple and does not need any special machines and tools. After baking, it can withstand the high temperature of LED for a long time without quality change. LED street lights, LED landscape lights, or LED billboards that are used outdoors will also face acid and alkali damage from wind and rain, acid rain, bird droppings, air dust, black smoke emissions, etc. Therefore, the spray type soft ceramic heat dissipation paint must have the characteristics of acid and alkali resistance, and the range of acid and alkali resistance is PH3 11, which can effectively protect the appearance of LED outdoor lamps from erosion. 100 watt led street light SL03 specification Model No.: SL03–100W Power(W): 100W Light Efficiency: 100–150Lm/W Voltage(V): AC100–277V CRI(Ra): >70 Power Factor: >0.95 CCT(K): 30006000 Environment Temperature :-4050℃ Life Time(H) : ≥50000 Ctn/Pcs: 1 LED: Epistar/CREE Model No.: SL02–180W Power(W): 180W Light Efficiency: 100–150Lm/W Voltage(V): AC100–277V CRI(Ra): >70 Power Factor: >0.95 CCT(K): 30006000 Environment Temperature :-4050℃ Life Time(H) : ≥50000 Ctn/Pcs: 1 LED: Epistar/CREE 100 watt led street light for sale 100 watt led street light for sale,Shanghai JingRui lighting is a professional enterprise integrating research and design, production, sales and service.Our main products include 100 watt led street light, LED Grow Light, HID Flood Light, Ballast and Bulb, etc. which are widely used for mobile light tower, construction sites, stadium, parking lot, road, ports and docks, etc. Free Quotes. Trained Specialists. Satisfaction Guaranteed. The faq of 100 watt led street light Q:Are you a manufacturer or a trade company? A:We are a manufacturer,specialize in making solar LED flood lights and solar LED street lights. Q:Can I buy samples placing orders? A:Yes.Please feel free to contact us. Q:How much is the freight cost of samples? A:It’s depends on weight,packing size and destination.Please contact us if you need,we can get the quote for you. Q:How do your factory control quality? A:We have 4 times inspection by QC before shipping.The first time is for raw material,the second and third times are for appearance and function,and the final is for packing. ·RELATED QUESTIONShould I get HID or LED headlights? Why?I'll tell you, my choice is LED headlights.The following is my understanding of HID and LED.Advantages of Xenon Lamp1. The color temperature of xenon lamp ranges from 3000K to 12000K, of which 3000K is pure yellow, with the strongest penetrability in rainy and foggy days.4300K white to yellow, is the most comprehensive color temperature in rain, fog, sunny days and many road conditions (this is the standard for the original high-grade cars).5500K is the most natural color that is slightly white and close to sunlight.The 6000K color temperature contains more blue components, thus presenting blue and white light.Simply put, the higher the color temperature, the whiter the color, and the poorer the relative penetration, the shorter the illumination distance.2. HID is three times higher than halogen lamps in brightness efficiency, which has an obvious effect on improving the visibility of driving at night and in fog.3. Xenon lamps emit more than 2 times the luminous flux of halogen lamps. At the same time, the efficiency of converting electric energy into light energy is also increased by more than 70% compared with halogen lamps. Therefore, Xenon lamps have a relatively high energy density and illumination intensity.4. Save 1/2 of electricity. Halogen lamps consume more than 60W of electricity while xenon lamps only need 35W of electricity.5. Since xenon lamps have no filament, the problem of scrapping due to filament breakage will not occur. The service life of xenon lamps is much longer than that of halogen lamps. The service life of xenon lamps is equivalent to the whole operation time in the average service life of automobiles.6. Xenon lamp will not go out instantly in case of failure but will go out (or light up quickly) by gradually darkening, so that drivers can gain time in driving at night and pull over in an emergency.Disadvantages1. The requirement of a light-gathering is high. Special xenon lamps must be used. There are two factors for not gathering light.(1) The mismatch between bulb and lamp leads to, for example, installation of xenon lamp light source for lamps using halogen lamp light source; (This is also why it is not effective for car owners to change xenon bulbs directly. )(2) Bulbs and lamps are not properly installed, and the focus is not properly adjusted, which requires professional and experienced light distributor.2. Some models with the self-checking function will have fault lights on when they are installed because the bulb power of the original car is high (55W) and the power of the xenon lamp is low (35W), so the modified car will give an alarm when its power is not enough. As a xenon lamp, its starting instantaneous current is 8A, while the original car was started at 6.2A, so the circuit settings of the original car do not match. Professional installers are required for decoding and matching.3. The quality of the product is not up to standard. Incorrect installation may cause electromagnetic interference. This requires a professional installation technician to install.Advantages of LED Lamps1. Long service life, generally up to tens of thousands or even hundreds of thousands of hours. In the future, LED will be used for automobile lighting lamps, and lamps will not need to be replaced throughout the service life of the automobile.2. High efficiency and low energy consumption. The LED light source can directly produce red, amber and other colors required by automobile lamps without color filtering, without loss, and the utilization rate of electric energy is as high as over 80%.3. The light quality is high and belongs to environmental protection products. Basically, there is no radiation and "green" light source.4. LED has a simple structure, internal support structure, and is sealed with transparent epoxy resin around, with good seismic performance. 5. No delay in lighting, fast lighting response speed (nanosecond), suitable for objects with fast-moving speed.6. It is suitable for low voltage operation and can be completely applied to automobiles.7. LED occupies a small volume. Designers can change the lamp mode at will, thus diversifying the car shape. Automobile manufacturers favor LED, which is completely determined by the advantages of LED itself.Of course, compared with xenon lamps, LED lamps also have the following disadvantages1. The requirements of lamps are extremely high-since the requirements of lamps are more stringent at the single point of the light-emitting focal plane, this problem is also the reason why the lighting effect of LED lamps is most affected.2. High cost-Take LED reversing lamps as an example. One LED reversing lamp is close to 30 yuan, while the price of one bulb is only 5 yuan, most of which is the cost of LED lamps. High prices cause ordinary cars to be unable to install LED lights and the market cannot be popularized.3. The difficulty in popularizing LED car headlights is due to the fact that the LED light source is installed in a relatively sealed headlamp assembly, which has poor heat dissipation and easy light attenuation due to poor heat dissipation treatment, thus affecting the service life of the headlamp.4. There is no unified industry standard and the quality of products is uneven.5. It is difficult to design a light type. Because the vehicle lighting is different from the domestic lighting, the width, range and range requirements of the vehicle lighting are much higher than those of the domestic lighting.In general, xenon lamps and LED lamps have their own advantages and disadvantages. Judging from the matching of current light sources and lamps, if the lighting effect is the final judgment standard, the effect of HID xenon lamps is obviously higher than that of LED lamps which are not perfect enough, but judging from the overall development trend of science and technology, LED lamps will definitely be the mainstream in the future.Maybe you want to know more about LEDs in cars, you can visit myblog(vantenled.blogspot.com) or mywebsite(www.vanten.co.uk). It will have some good idea
Led Street Light China
Led Street Light China
stock ranges from 28 million to 30 million. In recent years, the number of new street lamps is 15% — 20%, about 3 million — 6 million. According to the annual number of new street lamps are all LED lamps, calculated at 1000–2000 yuan per lamp, the annual growth is between 3 billion and 6 billion yuan. Development of The failure rate of over 6000 hours is less than 1%. Lighting accounts for about 19% of the world’s electricity consumption. If the global lighting system is twice as efficient as the existing one, it would be equivalent to removing half of Europe’s electricity consumption and heat exhaust. A global independent experiment has been set up recently. can save up to 85% of its energy. Market In December 2017, China produced 250 million sets of lamps and lighting devices, an increase of 12.45% over the same period last year. From January to December 2017, the national output of lamps and lighting devices reached 2.5 billion sets, an increase of 6.38% over the same period last year. From the output of provinces and cities, the output of lamps and lighting devices in Zhejiang Province reached 1.07 billion sets from January to December 2017, an increase of 9.13% over the previous year, accounting for 42.40% of the total national output; the output of lamps and lighting devices in Guangdong Province reached 870 million sets, a decrease of 44% over the previous year, accounting for 34.43% of the total national output. Led street light has become a hot product made in China and an attractive investment area. manufacturer Shanghai JingRui lighting is a professional enterprise integrating research and design, production, sales and service.Our main products include LED Flood Light, LED Street Light, LED Grow Light, HID Flood Light, Ballast and Bulb, etc. which are widely used for mobile light tower, construction sites, stadium, parking lot, road, ports and docks, etc. Categories of 1. According to the height of street lamp: high pole lamp, middle pole lamp, road lamp, courtyard lamp, lawn lamp, buried lamp; 2. According to the material of street lamp pole: hot-dip galvanized iron street lamp, hot-dip galvanized steel street lamp and stainless steel street lamp; 3. According to the shape: Chinese lamp, antique lamp, landscape lamp, single-arm street lamp, double-arm street lamp. 4. According to the mode of power supply: City circuit lamp, solar street lamp and wind-solar complementary street lamp productsSL01 ● Use imported integrated LED, high light efficiency, slow light depreciation ● Die-casting aluminum shell, surface electrostatic spraying, anti-corrosion treatment ● The structure of the people-oriented design concept, easy for installation and maintenanceSL02 ● The light body is designed on the basis of fluid dynamics, simple and decent, UV-resistance and corrosion treatment applied to the surface ● Modular designed, the power can be customized, meet the needs of various occasions ● Dustproof light body is helpful for LED dissipation, so the LED light can be worked on the best temperature environment, ensure the lamp source and power supply working timeSL08 ● High performance aluminum (ADC12) die-casting lamp heatsink with good thermal conductivity. ● Aluminum heatsink housing using Akzo Nobel powder coating or Dupont powder coating with high temperature baking process after polishing, cleaning, oil removal, repairing, sandblasting, with clear and gloss surface and strong corrosion resistance. ● The chip bottom of heat conducting surface processed by CNC machine to be smooth after heatsink powder coated, make the SMD and heatsink surface to be coincided with better heat conducting and heat dissipating.SL10 ● Integrated die-casting structure, all-metal lamp housing, reasonable design and beautiful shape. ● By using modular pluggable technology, make field servicing be done with only simple tools ● Achieve efficient heat dissipation performance by using Hot Honeycomb Principle and Full Structure Heat Dissipation Technology. ● Reach IP67protection level by using double coupling technology, super-high waterproof and dust-proof. The future of In the future, the LED street lamp driving power supply will also develop rapidly with the rapid promotion of the LED street lamp. It will be an opportunity for the LED street lamp driving power enterprises with technical and financial strength as support. It is predicted that by 2021, the share of LED in China’s lighting market will reach 80%. China will become the largest LED lighting market in the world, with a market scale exceeding trillion yuan. ·RELATED QUESTIONWhat times does Tribute in Light display outside of September 11, 2012?Located at West and Morris Streets in Lower Manhattan, the tribute of lights will begin at sunset of 9/11 (7:11pm) and fade away at dawn on September 12th (6:43am), though no formal service will be held. The Tribute is comprised of 44 7,000-watt xenon light bulbs arranged into two 48-foot squares inspired by shape and orientation of the twin towers. The Memorial illuminates up to 4 miles in the sky and can be seen from up to 30 miles away.
About [LED Tube] Meet Common Problems, LED Flood Lights, LED Industrial Mine Lamps, LED Tubes
About [LED Tube] Meet Common Problems, LED Flood Lights, LED Industrial Mine Lamps, LED Tubes
  Author :Green earth– LED Strip Lights manufacturersAs far as the LED tube we have seen, there is a structural, internal wiring, anti-electric shock protection, insulation resistance, and electrical strength, creepage distance and electrical gap, heat resistance and refractory. Different LED tubes are different from the light source and materials that determine different price and safety, and the LED tube has a built-in power supply, and the agency different decisions is different.Century Ruiguang Company Engineering Department Li Manager's current technical security issues related to LED tubes, for the type II anti-electric shock type, requires LED tube input contact to reinforce insulation resistance and electrical strength, many built-in power transformers and LED module aluminum substrate Improper installation, causing the test to pass. Or many companies use non-separated power supplies in order to save costs and power efficiency. Internal wiring is mainly linear and insulating thickness, mechanical damage, and insulating layer. The inside is basically can't be in contact with the lamp shell of the aluminum, and the insulation is enhanced. It is also necessary to avoid internal wires and power supply directly to contact the outer casing and prevent the wire from being broken. In terms of structure, it is necessary to prevent insulation of the lamp head, screw, and contact metal surface, and the corresponding lamp head plastic should be used to prevent melting. Since the screws of the LED tube are directly locked, they are required to pay attention to the creepage distance and electrical interval. The internal power supply and the aluminum housing are needed to be separated from the insulating sleeve to reach the power level. The lamp holder and the lamp body are relatively insulated to prevent leakage of the shell.Article Source: LED tube
About [LED Tube] Industry Case, LED Industrial Mine Lamp, LED Tube, LED Spotlight
About [LED Tube] Industry Case, LED Industrial Mine Lamp, LED Tube, LED Spotlight
  Author :Green earth– LED Strip Lights manufacturersIn 2014, the LED lighting industry was not destined to be an ordinary year. Thunder X illuminated, followed by Wuhan, Hubei, after Hangzhou, Zhejiang, once again“replace”Guangdong Shenzhen operations middle candidates; Yigong and Wu Zhengzheng broke up and the goods were 120 billion to buy, the original agent will be in the question, leaving a lot of topics worthy of the illumination. BeTwenty years ago, Guangzhou, there is a group of fresh young people, we all have simple wishes, this wish is just a little bit better for the days. They stepped on classic“Phoenix”Double bar bike, the street alley is delivered by a hardware store. They grow in plain, change in growth, very fast,“After the Yangtze River”, A batch of storm-free pre-sealing, the state-owned bulb manufacturing plant falls, another batch“Unique”The private lighting company founded it, which also laid a lot of a lot of a lot of lines.Replacement brands frequently in the short term, the loss of the dealer cannot be estimated. Huizhou's potential brand West X original Nanjing agent, from the west x brand I can't promote the promotion fees, I have to light your career with him.“Puff”Break up, turn the flower light.In the transformation of China's economy, our employment is increasing, and the warehousing capital is increasing, and the delivery capital is increasing, and the manufacturer is looking for a variety of increases, and the quotation is getting more flat. Many dealers are carrying a micro profession. Selling, and even no profit sale, and even some are still being sold.Article Source: LED tube
no data
Green Earth is continuously approaching different markets in various ways, we will keep on researching and designing innovative products, bring a better light to human beings. 
QUICK LINK
CONTACT US

Market cooperation : Pei Yin

E-mail : greenearthcn@greenearthcn.com

Phone : +86 13823531612

Supplier Cooperation : Zhi Song

E-mail : songzhi@green-earth.cn

Phone : +86 13588306599

ADDRESS
5-7F, Block 1, Industrial Park 29, Makan Village, Xili Town, Nanshan District, Shenzhen,China. 518055
FOLLOW US
   

Copyright © 2021 GREENEARTH  |  Sitemap

chat online
Please message us and we’ll be sure to respond ASAP, what product you intrested in?