Green Earth has become a more professional and full-fledged company since a decade development.

greenearthcn@greenearthcn.com   +86 13823531612       

How to Prepare for LED Solar Street Lamp Installation

  Author :Green earth– LED Strip Lights manufacturers

In order to standardize LED solar street light packaging, the operator must strictly implement the following packaging requirements.

1, 备

Refer to the LED solar street light box list to select the sheath line of the appropriate specifications (in general, the solar battery module sheathed line is selected 2×2.5mm2, light source protection sets 2×1.5mm2) and determine the length of each heel.

The length of the sheath line is determined: the length of each sheath line is taken from the LED solar street lamp structure. Solar battery packs, where there is a sufficient margin with the solar battery module connection, and the other end must grow and the bottom surface of the flange. The light source guard line There is a sufficient margin in which it is sufficient to connect to the light source, and the other end must grow and the bottom surface of the flange.

2, on the light bar assembly packaging

1) Pre-wear fine iron wire

Putting the No. 16 wire into the upper light bar assembly and leaves 300 mm over the end of the upper end of the light bar assembly, and the fine iron wire at the bottom of the light bar will be bent.

2) Wearing line

Put the prepared solar battery module (the red line of the component thread controller is pasted in advance with insulating rubber cloth, insulated rubber cloth around the 2 layer) The battery assembly is used to peel the battery pack 30mm line skin, and the core is fine After the wire's hook passes the core, tighten the core, then fix the core and fine iron wire with the insulating tape, twitch the wire on the top of the light pole to bring the component line out and leave a 500mm 1000mm (according to the light pole) Component modeling determination) margin, the assembly line at the bottom end of the light bar is tightly tightened with 200 mm nylon tie and placed in the upper light rod, and the assembly line at the top of the light stop is fixed to the light pole. Be careful not to touch the ribbon in the threading process.

3) Sheareline line is logified

The sheath line in the lower end of the lamp bar assembly is stripped with a sheath of the length of about 200mm, and then the solar battery assembly is made on both ends of the solar battery pack.”Identify, and you must ensure that the logo is clear and it is not easy to fall off.

Notice:

1. The solar cell module sheathed line is generally two, so the two wires should be prepared in the pre-wearing wire, and then wear a knot one by one. After each of the solar cell module sheathed line, the upper end of the sheath line is identified and fixed.

2, in the sheathed line, the blue core represents the negative electrode, the red line core is a positive electrode. The rules apply to the solar street light connection.

4) Pack, tied up the light bar assembly

The gas film pad with a width of 1500px is wound, and the gas film pad pressed portion is one-sixth (ie 250px), and the gas film pad should be wrapped around the 3 laps with the distant dynamic tape, and then use Wrawn rope wound, spacing is 100±10mm.

3, light pole assembly packaging

1) Fill in the lake name and accurately with the steel printing. The specific installation method is seen in the "Selection, Typing and Installation Specification of Lighting Workshop Nameplate".

2) pre-wear fine iron wire

Putting the No. 16 wire into the lower light bar assembly and leaves 300 mm overhead at both ends of the lower light bar assembly. Wipe the fine iron wire at the bottom of the lower light bar with a steel wire.

3) Wearing line

The 30mm wire is peeled off with the stripper tongs by the stripping clamp, and the core is tightened after returning the core from the lower end of the lower end of the lower light rod assembly, and then the line is used The core and fine iron wire are fixed firmly, and the wire on the top of the light pole take the light source out and leave a 1200mm 1800mm margin (according to the lamp arm structure determination), put the light line at the bottom of the light bar. In the lower light bar assembly, the light source line at the top of the lower light rod is fixed on the light rod, and not to touch the ribs during the threading process. Finally, put a fine iron wire in the lower light rod and leave 300 mm over the end of the lower light bar assembly and fixed the wire.

4) Set of lines

The sheath line under the lower end of the light rod assembly peels the length of about 200mm sheath, and then do the light source XXW at both ends of the solar battery pack.”Identify, and you must ensure that the logo is clear and it is not easy to fall off.

5) Pack, tied up the light bar assembly

The gas film pad with a width of 1500px is wound, and the gas film pad pressed portion is one-sixth (ie 250px), and the gas film pad should be wrapped around the 3 laps with the distant dynamic tape, and then use Wrawn rope wound, spacing is 100±10mm.

4, packaging lamp arm assembly

Wrap the lamp member with a width of 1500px, and the gas film pad pressed portion is one-sixth (ie 250px) of its width (ie 250px), and the gas film pad should be wrapped around 3 turns with a distant dynamic tape, then use Wrawn rope wound, spacing is 80±10mm.

5, packing solar battery pack angle steel box

The gas film pad with a width is 1500 px is wound around the solar cell module, and the gas film pad pressed portion is one of the widths (ie 250px), and the gas film pad is needed to be wrapped with a remote power tape. Circle, then wrap the straw rope, the spacing is 100±10mm.

1) Put the luminaire after assembly and debugging into the original packaging box, then seal the box with the distant power tape. When the sealing is sealed, first seal the middle of the box with the remote tape, then sealed with the sealed tape vertical direction, the distant dynamic tape is 80mm from the top edge of the top edge, where the position is in the middle of the box, requires remote power tape The end face is flat, and finally use the baler in both ends of the package.±Take a circle of tapes at 20mm.

2) Fill in the product model and quantity with the marker on the sign, and the sign is attached to the long face of the box.

6, battery and battery compartment packaging

To dry the battery compartment (in-electric storage battery) of the immersion test, the sheathed line from the threaded hose is tightened and fastened to the threaded hose. Then use the suitable gas film pad to wrap the wire hose and sheathed line and tighten with nylon. The outer poles of the sheath line are wrapped with an insulating tape.

7, solar battery pack packaging

The solar battery pack is packaged in a special packaging of Yixin electrical solar cells.

8, other accessories packaging

Other accessories refers to: Secondary bolts, nuts, and flat washers for securing solar cell modules, connect the bolts used in the upper and lower light rod assemblies, and fix the bolts, nuts, flat washers, and spring gaskets used for solar cell modules., Controller and controller Protective box, hatch key (triangle lock key), manual, warranty card box list and other standard parts.

Refer to the LED solar street light box list to receive the accessories and place it in the plastic package, and then put it into the box. Packaging box.

Put the test qualified controller (inverter) is placed in the original package, and then put it in the box with the remote power tape; the book, the certificate, the warranty card, the box list is put into the bag, then put it in The box above the box.

How to Prepare for LED Solar Street Lamp Installation 1

led related articles
About the Related Introduction of Ceiling Lights
About [LED Tube] Meet Common Problems, LED Flood Lights, LED Industrial Mine Lamps, LED Tubes
About [LED Tube] Industry Case, LED Industrial Mine Lamp, LED Tube, LED Spotlight
Question @LED Street Light About LED Street Lights
Special Technical Requirements About LED Street Lamps @LED Street Lamp
you might like
Lamp Part Products Case Flood Light
Led Green Earth Manufacture
Green Earth Brand Led Flood
Quality Green Earth Brand Led Lighting Suppliers
Led Strip Vendors Green Earth
the LED Downlight Accessories Are Sprayed with RAL9003 Oil. Green Earth Manufacture
Green Earth is continuously approaching different markets in various ways, we will keep on researching and designing innovative products, bring a better light to human beings. 
QUICK LINK
CONTACT US

Market cooperation : Pei Yin

E-mail : greenearthcn@greenearthcn.com

Phone : +86 13823531612

Supplier Cooperation : Zhi Song

E-mail : songzhi@green-earth.cn

Phone : +86 13588306599

ADDRESS
5-7F, Block 1, Industrial Park 29, Makan Village, Xili Town, Nanshan District, Shenzhen,China. 518055
FOLLOW US
   

Copyright © 2021 GREENEARTH  |  Sitemap

chat online
Please message us and we’ll be sure to respond ASAP, what product you intrested in?