Green Earth has become a more professional and full-fledged company since a decade development.

greenearthcn@greenearthcn.com +86 13823531612

Problems and Functional Analysis Needed in LED Underwater Lamp Installation

2022-04-28

Green Earth

　　Author ：Green earth– LED Strip Lights manufacturers

LED underwater lamps are generally LED light sources, and LEDs are called fourth-generation lighting light or green light sources, with energy saving, environmental protection, long life, small size. When it is powered, you can send a variety of colors, colorful, usually installed in the park or fountain pool.

The LED underwater lamp is a water bottom lamp produced by LED technology. Compared to traditional underwater lamps, the LED underwater lamp is more energy-saving and environmentally friendly, and the light is varied, and the decorative is stronger, which is widely used in a variety of landscape lighting systems. However, as a manufacturer of LED luminaires, some problems in the installation of the LED underwater lamp require special attention.

1. The LED underwater lamp should be powered by DC constant current power supply. Under constant current power control, the LED wall light, LED light, LED underwater lamp, LED buried lights will become small as the temperature of the LED chip is increased, so that the case is for LED underwater lamps. There is not much impact. However, if it is a constant pressure driver, the chip that causes the LED underwater lamp continuously increases the temperature rise, and it may even burn the LED underwater lamp when it is severe. Therefore, the LED underwater lamp should be powered by DC constant current power supply.

2, need to do anti-static measures. LED underwater lamp products should use certain anti-static measures during processing and installation, such as: Workbench should be grounded, workers should wear anti-static clothing, with anti-static rings, and with anti-static gloves, etc. Anti-static ion fan, but also to ensure that the air humidity in the installation is about 65%, so as to prevent the air to be too dry to produce static electricity. In addition, different quality grades of LED antistatic capacity is different, and the high-quality LED underwater lamp anti-static capacity is strong.

3. Pay attention to the seal of the LED product. No matter what kind of LED lamp products, as long as it is applied to outdoor, it faces moisture-proof, sealing problems, and the situation is even more likely to the LED underwater lamp. Sealing problems will not affect the service life of LED underwater lamp products.

1) Safety function

In the landscape, the choice of LED underwater lamps uses personal safety as the first element. The 12V voltage LED underwater lamp must be used in accordance with the requirements of the national standard.

2) Lighting function

The lighting function mainly refers to the luminance of the light source. It can choose different power LED underwater lamps according to the illumination height and the light area. Another feature of the lighting function is the color of the LED underwater lamp, which is generally red, yellow, green, blue, white, and can be used according to the application, irradiation objects and the atmosphere of creating.

3) Appearance and housing materials

Although the LED underwater lamp is used underwater, it is not very dedicated. However, the top and material is related to the specific gravity of the lamp. If the specific gravity is too small, a large buoyancy is generated, easy to loosen the fixed screw of the LED underwater lamp, so that the lamp is floating and too heavy and the lamp holder is difficult to support. At the same time, due to long-term use of water, the shell material should have a certain anti-corrosion function, and the surface lacquer is firm.

4) Economic

The economic performance of the LED underwater lamp refers to the sum of the one-time investment and operating costs of the lamp. In general, the quality is better than the LED underwater lamp. Its luminaire has a high price. It has a long service life. It has a small operating cost. It is, the quality of LED underwater lamps are poor, although the price is cheap, but often causes blindness due to leakage, leakage Not only added operational costs, and some even affect the acceptance of the entire project.

Problems and Functional Analysis Needed in LED Underwater Lamp Installation 1

GET IN TOUCH WITH Us

Led Green Earth Manufacture

Green Earth Brand Led Flood

Quality Green Earth Brand Led Lighting Suppliers

Led Strip Vendors Green Earth

the LED Downlight Accessories Are Sprayed with RAL9003 Oil. Green Earth Manufacture

About the Related Introduction of Ceiling Lights

　　Author ：Green earth– LED Strip Lights manufacturersThe lamp manufacturer produced with a lot of kinds, can bring us great convenience when using it, let's take a look at the related introduction of ceiling lights.First of all, it is characterized, there are many types commonly used in ceiling lamps, including square cover ceiling lights, pointed round ceiling lamps, etc., it can be directly installed on the ceiling, and it is easy to install, simple in style, very good in space lighting. Effect. I know its characteristics, the rest is the problem. The inside of the ceiling lamp generally has a ballast and loop tube, which can instantaneously start, and extend the life of the lamp and the power consumption is also low. The ceiling lamp has remote control and no remote control. It can be selected according to our needs.Introduction to the ceiling lamp, Xiaobian will introduce you to you, we can choose itself when using itself.

About [LED Tube] Meet Common Problems, LED Flood Lights, LED Industrial Mine Lamps, LED Tubes

　　Author ：Green earth– LED Strip Lights manufacturersAs far as the LED tube we have seen, there is a structural, internal wiring, anti-electric shock protection, insulation resistance, and electrical strength, creepage distance and electrical gap, heat resistance and refractory. Different LED tubes are different from the light source and materials that determine different price and safety, and the LED tube has a built-in power supply, and the agency different decisions is different.Century Ruiguang Company Engineering Department Li Manager's current technical security issues related to LED tubes, for the type II anti-electric shock type, requires LED tube input contact to reinforce insulation resistance and electrical strength, many built-in power transformers and LED module aluminum substrate Improper installation, causing the test to pass. Or many companies use non-separated power supplies in order to save costs and power efficiency. Internal wiring is mainly linear and insulating thickness, mechanical damage, and insulating layer. The inside is basically can't be in contact with the lamp shell of the aluminum, and the insulation is enhanced. It is also necessary to avoid internal wires and power supply directly to contact the outer casing and prevent the wire from being broken. In terms of structure, it is necessary to prevent insulation of the lamp head, screw, and contact metal surface, and the corresponding lamp head plastic should be used to prevent melting. Since the screws of the LED tube are directly locked, they are required to pay attention to the creepage distance and electrical interval. The internal power supply and the aluminum housing are needed to be separated from the insulating sleeve to reach the power level. The lamp holder and the lamp body are relatively insulated to prevent leakage of the shell.Article Source: LED tube

About [LED Tube] Industry Case, LED Industrial Mine Lamp, LED Tube, LED Spotlight

　　Author ：Green earth– LED Strip Lights manufacturersIn 2014, the LED lighting industry was not destined to be an ordinary year. Thunder X illuminated, followed by Wuhan, Hubei, after Hangzhou, Zhejiang, once again“replace”Guangdong Shenzhen operations middle candidates; Yigong and Wu Zhengzheng broke up and the goods were 120 billion to buy, the original agent will be in the question, leaving a lot of topics worthy of the illumination. BeTwenty years ago, Guangzhou, there is a group of fresh young people, we all have simple wishes, this wish is just a little bit better for the days. They stepped on classic“Phoenix”Double bar bike, the street alley is delivered by a hardware store. They grow in plain, change in growth, very fast,“After the Yangtze River”, A batch of storm-free pre-sealing, the state-owned bulb manufacturing plant falls, another batch“Unique”The private lighting company founded it, which also laid a lot of a lot of a lot of lines.Replacement brands frequently in the short term, the loss of the dealer cannot be estimated. Huizhou's potential brand West X original Nanjing agent, from the west x brand I can't promote the promotion fees, I have to light your career with him.“Puff”Break up, turn the flower light.In the transformation of China's economy, our employment is increasing, and the warehousing capital is increasing, and the delivery capital is increasing, and the manufacturer is looking for a variety of increases, and the quotation is getting more flat. Many dealers are carrying a micro profession. Selling, and even no profit sale, and even some are still being sold.Article Source: LED tube

Question @LED Street Light About LED Street Lights

　　Author ：Green earth– LED Strip Lights manufacturersDue to technical content, complicated components, some high-power lamps will be much more than ordinary sodium lamps, so it is more required for the corresponding support material. In order to reduce the self-weight of the LED street lamps as much as possible, our company selects lightweight raw materials as much as possible.Our company's LED street lights, new design, structure, full of modern breath, in line with the trend of the times. Some heat dissipation design, has a good quality assurance, worthy of trust!

Special Technical Requirements About LED Street Lamps @LED Street Lamp

　　Author ：Green earth– LED Strip Lights manufacturersThere are many indexes of the LED street lamp, the lamp energy, the protection level, the average life, the use of temperature, the use of heat sink temperature, immunity, light distribution characteristics, etc.When the ED street light is operating at a nominal rated power supply voltage and rated frequency, the difference in power and rated power should not be greater than 10%, and the power factor should not be less than 0.92, and the LED stream protection level A-level product should not Low than IP67; B-class products should not be lower than IP66; C-class products should not be IP65, the rated average life of the LED street light should not be less than 30000h, the rated temperature Tc value of the LED street light should not be greater than 58 C, the lights in the lamp The sink temperature should not be greater than 65 C. The voltage protection level of the surge suppression performance should not be less than 2kV and 4KV. When some LED bulbs in the luminaire are extinguished, the spot shape and the road surface illumination uniformity should not change significantly. .If you want to know more, you can call our company directly. Welcome everyone to consult! Professional production, worthy of trust!

Question About LED Street Lamp Cooling Mode

　　Author ：Green earth– LED Strip Lights manufacturersNow LED lighting technology is increasingly mature, but the LED street base is on the heat transfer or heat dissipation problem, what we can take is still limited, so today Xiaobian should talk about the problem of choice for LED street lamp heat dissipation mode, hoping Help everyone.At present, the heat dissipation of the LED street base is mainly divided into natural convection heat, adding fan forced heat dissipation, heat pipe and circuit heat pipe heat dissipation, and the installation fan forced heat dissipation mode is relatively complicated and the reliability is relatively low, and heat pipe and circuit heat pipe heat The cost of the way is compared, and because the LED street lamp is often used outdoors, the heat dissipation surface is located on the side and the body type is limited, and these factors are too friendly for other two ways, but However, it is necessary to play air naturally, the advantages of the flow of the heat dissipation, so the LED streetlights should choose natural convection heat when selecting a heat dissipation method.

How Much Do You Know About the LED Street Lamp? @Led Street Lamp

　　Author ：Green earth– LED Strip Lights manufacturersThe traditional LED street lamp design is paying attention to the number of LEDs, and it is not much for its heat dissipation effect, in fact, it is not right. In life, with the increase in the number of LEDs, the heat dissipation design is also required, and the traditional heat transfer means is conducted, convection, Radiation and phase change heat, so we have to solve problems on the issue.LED street lamp heat dissipation technology uses a heat-insulating board mode, because the copper plate is relatively thick, so it is not very convenient to use, and there is still a risk of dangerousness, if you encounter a typhoon, or the earthquake may be an uneasy factor, so now It is a needle heat dissipation technology.Such a technique makes the heat dissipation, so that the LED junction is lower than the ordinary heat sink at least 15 C, and has good waterproof performance, there is basically no uneasiness due to weight, so Xiao Bian also likes this. The lamp is easy to install.The heat dissipation method of the lamp holder can be divided into a variety of forms, heat pipes, circuit heat pipe heat dissipation, installed fan forced heat dissipation, natural convection heat, etc. Low, so smallIt is recommended to use natural convective heat to reduce, safe and low cost.

Selection of Internal Components Within LED Street Lamps

　　Author ：Green earth– LED Strip Lights manufacturersAt present, there are two kinds of LED street lights in the market: integrated lamps and traditional street lamps.LED street lamp manufacturers are mainly composed of high-power LED particles, aluminum-based PCB, radiator, drive power, housing, and lens (optional).High-power LED: mainly selective light flux (80 to 100 LM), light decay, color temperature 5000-7000K.Aluminum substrate: highly thermally conductive aluminum alloy, mainly aluminum purity, excellent copper materialRadiator: High heat transfer, there is a special heat dissipation method in the market, such as heat pipe heat dissipation, liquid cooling, electric fan heat, etc.Drive power supply: high efficiency (more than 90%), current output is stable, small ripple, optimal energy over EMC.Shell: The demand is to facilitate light source heat, as for the appearance, due to market demand.Leisure: high light transmittance (90%), anti-UV, rectangular spot, etc.Jiangsu Qi Zhao Lighting Co., Ltd. is a professional manufacturer, lithium battery solar street light, high pole light, lithium battery solar street light, garden light, landscape light, wait, etc. New and old customers come to consult.

Installation of LED Flood Lights Using @led Flood Light

　　Author ：Green earth– LED Strip Lights manufacturersWhen the LED floodlight is installed, pay attention to tighten the hanging ring, the ring is M20 thread. Put the hanging ring into the hook and place it smoothly. When installing the lamp, the wiring is closed and the wiring is closed to prevent leakage. When an external power cord, there is a need to take the corresponding waterproof and water leakage measures. The luminaire cannot violate fire regulations when used. Installation, find professional electricians, 0.75mm2 three-core cable wiring mode is the red line for the fire line, the blue line is zero line, and the yellow green line is ground.Precautions for installing are the above points, pay attention to the product using operating voltages during use, please do not run the operating voltage range. Because the lamp has glass accessories, please pay attention to lightly, do not override. The products produced by Paris have good warranty, after-sales service. Under normal use conditions, quality assurance is based on the correct preservation, installation, use and maintenance of the product; due to improper installation, the product is damaged, which is damaged, not within the scope of this guarantee; Quality issues, the company is solved in the warranty period.

Eight-meter Solar LED Stream Pole Strength Calculation

　　Author ：Green earth– LED Strip Lights manufacturersEight-meter solar LED stream pole strength calculationThe following explanation is determined according to GB50135-2006 "Tower Structural Design Specification". Known Conditions are calculated in maximum wind speed V = 36m / s, 12 typhoon. Solar LED Street Light Bar Material Q235 Wait Stress [σ] = 225000kn / m2.Solar LED street lamp lever shape size 8m, light pole height h = 8m, wall thicknessδ5, upper mouth diameter D = 60, lower mouth diameter D = 165 . The upper part of the light pole is in the upper arm length size is l = 1.3M lamp bottom plate flange 420 ×420 .Solar LED street lamp foundation size, foundation profile 0.6m×0.6m, buried depth 1.5m, ground bolt hole distance 320 ×320 , the bolt diameter M24 is four.Solar LED street light pole strength calculation: standard wind pressure calculation, basic wind pressure is W0 = 0.8kN / m2 by wind speed 36m / s, the standard wind pressure W = W0·KT = 0.8×1.1 = 0.88kn / m2. The wind pressure adjustment coefficient KT takes 1.1.The wind calculation of the solar LED street lamp holder stroke light headμS, conical rod body 8.7 wind pressure high speed change coefficientμZ, take 0.9, the light pole is in the wind area S rod = 1.06m2, the street lamp is in the wind area S light = 0.3m2, the light rod is affected by the wind F rod = W·μYes·μexist·S rod = 0.588KN, the lamp head is affected by wind F light = W·μYes·μexist·S light = 0.166knThe total bending moment of the solar LED street lamp lever is calculated, the light pole bending moment M rod = f·H / 2 = 1.176KN·m, the lamp head to the bending moment of the pole, M light = F light·H = 1.328KN·M total bending moment,σM = M rod M lamp = 2.504 kN·NoSolar LED street light pole bending modulus calculation. WZ =πD 4—D4 / d = 3.14×(0.1654-0.1554) / 32/0.165=0.0000976m3.Calculation of solar LED street light pole bending stress. Bending stressσσ=σM / W0 = 25661.8kn / m2σσAs seen from the above calculations, the strength of the solar LED street light pole is sufficient. The geodial bolt intensity check, the wind direction is the diagonal, the tension of the terrain bolt is the maximum N =σM×Y /σY²= 2.504×0.327 / 0.327²2×0.1²= 6045KN, safety factor k take 2.5 floor bolts M24 effective cross-sectional area, s = 314 ², Q235 steel yield limit,σS = 235n / ², Licensed pull N =σYes×S / K = 235×314 / 2.5 = 295KN> n = 645KN, and the ternary bolts are more than four M24.YWX [Excellent Promotion Screen 18013196696]

Green Earth is continuously approaching different markets in various ways, we will keep on researching and designing innovative products, bring a better light to human beings.

QUICK LINK